user_974580 (31)
C.S. Johnson over center pelican hook
Easy to operate under load
Investment cast stainless steel
5/16” stud
Comes with coated stainless 3/16” wire...
Easy to open and close pelican hooks for lifeline gate
Takes 5/16” LH stud
Quality product made by Merriman
Compare with $75 new for one
All 4 for...
Clever device for picking up a mooring
Works with a simple in and out motion
Works with any size mooring line and is suitable for boats up to 50'
W...
Lewmar Windlass Clutch Nut Lever (Wrench)
Used for tightening or releasing windlass free fall mechanism, and manual operation if required.
Appl...
Reliance MDR-2 zinc
2-13/16"
Includes two halves for securing to rudder or trim tab, and hardware.
Zinc anode for use in salt water.
New
STA-LOK stud
Fits 9/32” or 7 mm 1 X 19 wire
Stud is ½ x 20 TPI.
Product #036-07
Comes with 2 new wedges, one for standard wire, one for Dyform wir...
Standard Horizon DS45 Depth Sounder
Was a spare for the boat I recently sold.
Has been tested and works fine.
Fits in a 4.25” hole
Buy as a spare:...
40 flags in total
Each flag is about 10 inches X 12 inches
The run of flags is about 75 feet, with a total length of line about 85 feet.
The flags ...
PFD automatically inflates upon immersion in water
Inflation can be manually launched
Can be inflated orally
Built in sailing harness designed to p...
Polyform PG-1 Corner Dock Bumper
Measures 10 x 10 inches.
Polyform PG-2 Straight Dock Bumper
Measures 18 inches.
Protect your boat gelcoat and...
Made by Nico Fico, now Ronstan, Model 6741
Snap shackle allows quick setup, block easily opens to install line, and closes securely.
Cushioned ...
Range: O-5000 RPM
Yanmar Part Number: 129271-91210, 129271-91211, 164100-50100
Fits: Yanmar: 1GM, 1GM10, 2GM20, 2YM15, 3GM30, 3YM20, 3YM30, 3J...
One Forespar Marelon 3/4” flush head thru-hull, ball valve, and tailpiece.
One Forespar Marelon 3/4” flush head thru-hull, seacock valve, and tailp...
Moulded mooring snubber in EPDM Rubber with 6 rope holes.
Absorbs shock loads and relieve tension on lines and deck fittings.
Heavy duty: Up to ¾...
-8 circuits
-5/16” diameter solid copper bolts
-Solid copper bus bar 1/4" x 2" x 5 1/2"
-Mounted on bakelite plate: 4” x 6 ½” x 3/8”
-New conditi...
Heavy Duty spinnaker pole slider for 1 ¼” t-track
Made of investment cast stainless steel
Ring just under .500" in diameter.
Spring pin that locks ...
Two Backing Plates for Andersen 40 winches, self-tailing or non self tailing.
Custom made of marine grade aluminum, 3/16” thick.
100 mm bolt circle,...
Works with Standard Horizon GPS CP 155C, CP175C, and CP1000C. May work with other units.
This is the “smart antenna” where a portion of the GPS’s br...
Functional and looks good in the galley or head.
16 inches x 3 inches by 1 3/4 inches.
Nicely made by Seateak.
New, never used.
Compare with $70...
Dynaline Cable cutters.
Aluminum drop forged handles and heat treated blades.
Capacity: up to 5/8" diameter’
23" overall length’
Used for:
-gen...
Low drag folding prop
This shape has more blade area than the Martec elliptical style
Motors better and unfolds more reliably
1 inch bore
Right ha...
Two Barient 21 2 speed winches
Base: 5 ½ inches
Height: 5 ½ inches
Drum diameter: 2 ¾ inches
Drum material: Anodized Aluminum
Rope friction s...
Turned clear teak
36 inches long
1 ½ inches mid height
1 ¼ inches at base
Cast aluminum base and mounting hardware included
In as new condition
Well built jib/genoa in as new condition
Luff: 36.25 feet
Foot: 16.75 feet
Leech: 28.25 feet
Sewn leather on tack, clew, and head
Whipping aro...
Rule 1300 gph bilge pump
New, never installed
7.5 amp motor
Jabsco bilge pump level switch
15 amp rated
Turns on at 2 1/4” water level. Turns o...
user_974580
user_974580